Choose a Measurement
Select a measurement and convert between different units
Single conversion
To convert from Megavolt-Ampere Reactive (MVAR) to Millivolt-Ampere Reactive (mVAR), use the following formula:
Let's convert 5 Megavolt-Ampere Reactive (MVAR) to Millivolt-Ampere Reactive (mVAR).
Using the formula:
Therefore, 5 Megavolt-Ampere Reactive (MVAR) is equal to Millivolt-Ampere Reactive (mVAR).
Here are some quick reference conversions from Megavolt-Ampere Reactive (MVAR) to Millivolt-Ampere Reactive (mVAR):
| Megavolt-Amperes Reactive | Millivolt-Amperes Reactive |
|---|---|
| 0.000001 MVAR | mVAR |
| 0.001 MVAR | mVAR |
| 0.1 MVAR | mVAR |
| 1 MVAR | mVAR |
| 2 MVAR | mVAR |
| 3 MVAR | mVAR |
| 4 MVAR | mVAR |
| 5 MVAR | mVAR |
| 6 MVAR | mVAR |
| 7 MVAR | mVAR |
| 8 MVAR | mVAR |
| 9 MVAR | mVAR |
| 10 MVAR | mVAR |
| 20 MVAR | mVAR |
| 30 MVAR | mVAR |
| 40 MVAR | mVAR |
| 50 MVAR | mVAR |
| 100 MVAR | mVAR |
| 1000 MVAR | mVAR |
| 10000 MVAR | mVAR |
For all Reactive Power converters, choose units using the From/To dropdowns above.
A Megavolt-Ampere Reactive (MVAR) is a unit used to measure reactive power in an electrical system.
Think of it as a measurement for a type of "unproductive" power that doesn't do real work, but is still essential for the system to operate.
One MVAR is equal to one million volt-amperes reactive (VAR).
MVAR is a key measurement used in power factor correction. Here's a simple breakdown:
Essential but "Unproductive": Some equipment, like motors and transformers, need reactive power (measured in MVAR) to create magnetic fields just to run.
The Problem: This reactive power doesn't do any useful work (like turning the motor's shaft). High levels of MVAR in a system lead to a "poor power factor."
Why It's Bad: A poor power factor is inefficient. It causes wasted energy, higher electricity bills, and extra strain on the electrical grid.
The Solution: Utility companies and large facilities install equipment (like capacitor banks) to balance these MVARs. The goal is to get the power factor as close to 1.0 (or 100%) as possible, which is the most efficient state.
It's easy to confuse reactive power (MVAR) with "real" power, which is measured in Megawatts (MW).
Megawatts (MW): This is the "real" or "active" power. It's the power that does useful work, like lighting a bulb, heating a room, or turning a motor's shaft.
Megavolt-Amperes Reactive (MVAR): This is the "reactive" or "unproductive" power. It doesn't do useful work, but it's still essential for creating the magnetic and electric fields that allow many types of AC equipment to operate.
Beyond efficiency, balancing MVARs is fundamental for maintaining voltage stability across the electrical grid. Think of it as managing "pressure" in the system.
Too Few MVARs: An inadequate supply of reactive power causes the system's voltage to drop. This can lead to "voltage sag" (like dimming lights), equipment malfunction, or even blackouts.
Too Many MVARs: An excess of reactive power causes "over-voltage." This high-voltage condition can damage sensitive electronics and equipment.
Grid operators constantly manage MVARs to keep the voltage stable and ensure you receive reliable electricity.
A Millivolt-Ampere Reactive (mVAR) is a small unit used to measure reactive power.
Think of reactive power as the "helper" power in an electrical circuit. It doesn't do the actual work (like lighting a bulb), but it's essential for components like motors and transformers to function.
An mVAR is tiny: it's equal to one-thousandth of a single Volt-Ampere Reactive (VAR).
In an AC circuit, you have two types of power. Real power (measured in milliwatts, mW) does the actual work, like spinning a motor. Reactive power (measured in mVAR) is the "non-working" power that builds magnetic and electric fields to help the motor spin.
The problem is that too much reactive power leads to a poor power factor. This is a sign of inefficiency—it means your system is drawing more total power than it's actually using for work.
Managing reactive power, even at the small mVAR scale, is key to improving energy efficiency and keeping voltage levels stable in sensitive electronics.
The power triangle is a simple diagram that shows how these three types of power relate. Imagine a right-angle triangle:
This relationship is shown by the formula (mVA)2 = (mW)2 + (mVAR)2.
For engineers, the goal is to make the reactive power (mVAR) side as small as possible. This makes the total power (mVA) and the real power (mW) almost equal, which means the circuit is very efficient.
You won't hear about mVAR when discussing a city's power grid (they use much larger units like kVAR or MVAR).
Instead, the Millivolt-Ampere Reactive is crucial for low-power electronics.
Engineers use mVAR measurements in labs when designing or testing individual components like:
Precise mVAR readings help them understand the "reactive properties" of these tiny parts, ensuring that a final product (like your smartphone or computer) runs as efficiently as possible.